Plant Performance Working Groups

Cooperation in Reactor Design Evaluation and Licensing (CORDEL)

Chair: Zhou Fang (SNERDI) 
Deputy Chairs: Shin-Wan Kim (KEPCO E&C); Franck Lignini (Framatome); Tom Bergman (NuScale); Nawal Prinja (Jacobs)
Staff Directors: Byung-Chan Na (Director of CORDEL), Allan Carson and Ronan Tanguy

CORDEL’s mission is to promote a worldwide nuclear regulatory environment where internationally accepted standardized reactor designs can be widely deployed without major design changes at the national level. In practice, this would mean that generic design certification and safety evaluations approved by a recognized competent authority would be acceptable in other countries. 

CORDEL acts as industry’s voice in the areas of reactor design standardization, interacting with the International Atomic Energy Agency (IAEA), OECD/Nuclear Energy Agency (NEA)’s Committee on Nuclear Regulatory Activities (CNRA), European Nuclear Installations Safety Standards Initiative (ENISS), European Utility Requirements for LWR Power Plants (EUR), International Electrotechnical Commission (IEC), and the Standards Development Organization Convergence Board (SDO Board). 

In 2019, a new CORDEL Strategic Plan for 2019-2023 was issued, focusing on both new-build and long-term operation aspects of nuclear power plants. 

The key achievements of the CORDEL Task Forces in 2020, as well as planned tasks for 2021, are described below: 
 
Mechnical Codes and Standards Task Force
Chair: Nawal Prinja (Jacobs)  
Deputy Chair: Frédéric Beaud (EDF)

The Mechanical Codes and Standards Task Force (MCSTF) of the CORDEL Working Group was set up in 2010 to collaborate with the Standards Development Organizations Convergence Board (SDO Board) and the Multinational Design Evaluation Program (MDEP) Codes and Standards Working Group (CSWG) on the international convergence of mechanical codes and standards, related to the design of nuclear power plant’s components important to safety. During 2018, the work of MDEP Codes and Standards Working Group (CSWG) was transferred to the Working Group on Codes and Standards Working Group (WGCS) under the Committee of Nuclear Regulatory Activities (CNRA) of the OECD/Nuclear Energy Agency (NEA). The Task Force maintains close cooperation with the CNRA/WGCS.

Currently, the MCSTF has two pilot projects: fatigue life analysis and non-linear analysis. The Task Force completed its work on comparison of code requirements for fatigue analysis, publishing a report on “Comparison of Pressure Vessel Fatigue Codified Design Rules Based on S-N Approach” in July 2020. The Task Force published another report on “Assessment of Non-Linear Benchmark Results” in September 2020. The report contains the analyses and findings of ten sets of international benchmark results. A follow-up report is being completed, which recommends industry practices to be used in non-linear analysis.
 
Design Change Management Task Force
Co-Chairs: Jinxing Yan (SNERDI); Vacant
 
The Task Force revisited its scope and work programme in 2018. The Task Force contributes to work to facilitate the sharing of design change information on common nuclear power plant designs among different utilities, owners groups, and international organizations, and to maintain a dialogue with WANO and the IAEA on the responsibilities of operators on how they manage their fleets and cooperate internationally to keep a high degree of standardization.  

Licensing and Permitting Task Force
Chairs: Claude Mayoral (Edvance)

The Task Force has worked on the concept of a reference plant which could be more easily licensed in a given country by taking advantage of an acceptance of the reference plant design by a competent safety authority. The report on reference plant concept was published at the end of 2019. The Task Force continues to benchmark leading practices regarding licensing and promotes innovation leading to more efficient licensing processes. An ongoing joint project with Small Modular Reactor Task Force is country specific approaches to licensing and the required design maturity level of SMRs to engage regulators in licensing activities. A report from this activity will be issued in early 2021. In addition, the Task Force is working on the topic of different interpretations of regulatory requirements assessing various cases identified.  


IAEA Nuclear Safety Standards Task Force
Chair: Frank Lignini (Framatome)  
Deputy Chair: Robert Vesecky (CEZ,a.s.)

This Task Force actively contributes to the IAEA Nuclear Safety Standards Committee (NUSSC), providing consolidated industry inputs and feedback. In 2020, the focus was on Chemistry Programme for Water Cooled Nuclear Power Plants, Equipment Qualification for Nuclear Installations, Development and Application of Level 2 Probabilistic Safety Assessment for Nuclear Power Plants, Modifications to Nuclear Power Plants, and  Maintenance, Testing, Surveillance and Inspection in Nuclear Power Plants. The Task Force took part of the NUSSC’s working group on Safety Guide on Assessment of the Application of General Requirements for Design of Nuclear Power Plants and provided the IAEA with industry inputs to the safety guide update. The Task Force closely collaborate with ENISS and EUR to avoid duplication.


Digital Instrumentation & Control Task Force
Chair: Johannes Pickelmann (Framatome)  
Deputy Chair: Alan Poole (Jacobs)  

The Task Force continues to work on defence-in-depth and diversity aspects as well as on safety classification related questions. A revision of the report on the comparison of key concepts following comments by the OECD/NEA CNRA-Working Group on Digital I&C (WGDIC) and changes in national definitions was published in 2019. Similarly, the report on safety classification for I&C Systems in Nuclear Power Plants - Current Status & Difficulties was revised taking into account comments from CNRA-WGDIC and published in March 2020. The Task Force published another document on International Nuclear I&C and Electrical System Standards Tables with URLs in May 2020, which brings together the related standards used by the Institute of Electrical and Electronics Engineers (IEEE) and International Electrotechnical Commission (IEC) communities.

The Task Force published a report on “I&C Modernization – Current Status and Difficulties” in September 2020, and is currently discussing topics related to Other topics being currently discussed for future activities are related to cybersecurity and FPGAs for future activities. The Task Force will maintain its efforts to increase the visibility of its work within relevant SDOs and international organizations (IEEE, NEA CNRA, etc), and continue to interact with IAEA in the development of relevant TECDOCs.
  

Small Modular Reactor Task Force 
Chair: Tom Bergman (NUScale Power)  
Deputy Chair: TBC

The Task Force promotes application of the CORDEL model to global SMR deployment, presenting and discussing it at relevant international fora, such as the IAEA SMR regulators’ forum and INPRO. The Task Force provided industry’s common comments on the Phase 2 interim reports of the IAEA SMR regulators’ forum in June 2020.The Task Force is currently working on a joint project with the LPTF to define country specific approaches to licensing and the required design maturity level of SMRs to engage regulators in licensing activities. This project is also aiming to identify best practices and the level of readiness of existing licensing frameworks for new reactors and builds upon its previous report on the facilitation of international licensing of SMR’s. The resulting report will be published in early 2021. The Task Force will continue to develop proposals for more innovative and efficient licensing of SMRs, through looking at topics, such as inherent safety features and passive safety system capability justification; changes needed in the regulatory/licensing framework for non-LWR/advanced reactors; security approaches and non-proliferation issues; emergency planning zones (EPZ). The Task Force is closely cooperating with the Economics Working Group and Law Working Group at the World Nuclear Association.  

Supply Chain

Chair: Laurent-Olivier Coudeyre (EDF)  
Staff Director: TBC

The Group supports members in monitoring and identifying market trends, providing guidance on timely, consistent and efficient plant construction, and in communicating with stakeholders on industrial developments. In 2018, links with the World Association of Nuclear Operators (WANO) and the European industry association FORATOM were strengthened to avoid duplication and help amplify industry’s voice. 

The Group reports regularly to the Multinational Design Evaluation Programme’s (MDEP’s) Vendor Inspection Coordination Working Group (VICWG). The Staff Director assisted the Nuclear Energy Agency and the VICWG in organising a workshop on supply chain management in Paris in November 2018. It continues to work with the Nuclear Quality Standard Association to help ensure that the new quality management standard for the nuclear supply chain published by the International Organization for Standardization (ISO 19443) meets the needs and aspirations of licensees and technology vendors.A Memorandum of Understanding between a number of operators and reactor vendors and the World Nuclear Association to devise a road map for a strengthened system for qualifying auditors in certifying to the standard was agreed in late 2018.
 
The report of the New Build Lesson-learning Task Force, which was published in April 2018, attracted considerable interest.
 

Capacity Optimization

Co-Chairs: Mike Baron (Global Nuclear Associates) and Abderrahim Al Mazouzi (EDF)  
Staff Director: Ronan Tanguy

The Group was set up as a forum for discussing means by which nuclear power plant operators worldwide can improve the performance of their plants in areas such as maintenance and availability. Its recent focus, prompted by the average age of the global fleet reaching over 30 years, has been in the area of long-term operations (LTO). The LTO Task Force monitors existing work performed by WANO, NEA and IAEA in this field, and has produced a technical position paper to support outreach to policy makers regarding the feasibility and importance of continued operation of the existing fleet. The Task Force will also be a forum for industry, including vendors and utilities, to share leading practice in this field. 

Waste Management and Decommissioning 

Chair: Mike Pieraccini (EDF)  
Staff Director: Alexandre de Ruvo 

The Group monitors trends in waste management strategies on both the international and local level, and seeks to establish a consensus for a more effective system of nuclear waste management and decommissioning. The Group promotes resource efficiency through the appropriate re-use and recycling of material, and the safe long-term disposal of radioactive wastes from nuclear sites as prescribed in national regulation. Additionally, it cooperates with other Working Groups on topics of mutual interest, such as the radiological protection of workers during decommissioning, or with regard to multinational repositories.

In 2019, the Working Group published a methodological guide for managing waste from decommissioning. The guide covers various strategic, technical and economic aspects of nuclear waste management. The conclusions of this report are actively promoted internationally through conferences and technical papers to which the WM&D group members are involved with. 

The Group is regularly represented and actively contributes to various international organisations and technical committee such as the IAEA’s International Radioactive Waste Technical Committee (WATEC), The IAEA’s Status and Trends in Spent Fuel and Radioactive Waste Management report, the NEA’s Working Party on Deep Geological Repositories and Nuclear Liability (WPDGR) or the United Nations Economic Commission for Europe (UNECE) report.

 

Contact Us

World Nuclear Association


Tower House, 10 Southampton Street
London WC2E 7HA
United Kingdom

 


 

 


 

t: +44 (0)20 7451 1520
f: +44 (0)20 7839 1501

events@world-nuclear.org